Introduction
When it comes to your PCB via size selection you want to choose the correct PCB via size for optimal electrical performance, effective thermal management and for good structural integrity. This guide will drill down into PCB via size standards, types, aspect ratios, and important design guidelines to assist in improving your PCB.
What Is a PCB Via?
A PCB via, or vertical interconnect access, is a very tiny, small and copper plated hole crossing printed circuit board. Signals pass between different layers of the board; it connects different layers of the board. To do their job, the PCB depends on these connections. There are many kinds of vias. Mechanically drilled through hole vias are being used. But rather than lasers, blind vias are made, and they only connect certain layers. The purpose of each via type is specific during PCB designing. Electrical connections should stay strong, otherwise your PCB wouldn’t operate correctly.

Standard Via Sizes
Most PCBs have a standard via size of about 10 mils. After plating, this size has shrunk to 7 mils. However, via size, isn’t fixed. This is dependent on board thickness and has an aspect ratio. Usually, micro vias, around 4 mils tall, are smaller than vias. They can then be drilled by use of laser or mechanically. A particular requirement of laser drilled vias is. And they require at least 3 mils of spacing between layers.

PCB Via Types
Through-Hole Vias
The most common type in PCB design. That’s a hole that goes all the way through the board. It bridges all the layers together. It is used often for high current connections. The board becomes more durable by adding strength with through hole vias.
Blind Vias
It connects the outer exposed layer to one or more sublayers of the PCB. It won’t go the entire way through the board. High density designs with no space are where blind vias can come in use. They can do layer connections, without the full through hole. It’s been useful because it conserves valuable board space. Furthermore, it helps to place things more compactly. In small, complex boards, blind vias are required.
Buried Vias
It joins two or more of the inner layers of a PCB together. It doesn’t hit the outer layer at all. Multiple vias per or on a level, usually a via level due to size and opacity considerations, is a good route if high density design is necessary. You don’t need a lot of space to make lots of connections. Buried vias cut down on space taking up your board. They allow you to connect more without staying up to larger PCBs.
Stacked Vias
Drilled on top of one another. In high density PCBs, this type of via is very useful. Lots of connections fit in one small space. Space is saved on your board by stacked vias. It allows you to add more connections without increasing size of the board.
Staggered Vias
It links up layers of a PCB. They don’t touch each other directly. They exist in high density interconnects and multilayer designs quite often. Optimized routing is possible using staggered vias to eliminate signal interference. In high frequency they reduce impedance. That’s less design work and no via copper filling required for staggered vias.
Skip Vias
They are a kind of a blind via. Pads are connected to another layer. They’re used often in high density interconnect (HDI) PCBs. Links both sides of a trace as well. It reduce manual routing time. They eliminate buried vias between levels. In addition, it also solves the reliability problems that can arise with stacked blind-buried vias.
Microvias
A very small hole in a PCB. Typically it is less than 6 mils in size. This is the perfect type of via for high density designs. Many things can fit where space is tight. High frequency applications are also well suited to microvias. They are good for keeping signals strong and clear. However overall signal quality is improved using micro vias. It better allows for performance in small devices.
Vias in Pad
This was a hole under the component’s pad. The reason is that this type of via is really good for high density PCB design. Where every bit counts, it saves space. A direct connection to the board via the via-in-pad is achieved. This decreases the trace length and thereby enhances signal quality. And it also lowers the risk of solder bridging. The conductive material is filled in during the PCB assembly.
Via Tenting
This is a situation when you plate a via. The solder mask gives a protective layer to this small hole. Tenting protects the via from moisture, dust or chemicals. They can cause corrosion and short circuit. Plated through holes which electrical signals pass between layers because of vias. Reliable and high performance PCBs rely on tenting. It is especially true for high density interconnect (HDI) and flexible designs. It prevents solder wicking as well. This is where solder gets away from solder pads.

Aspect Ratios for Vias
This has to do with plating out copper inside vias. It’s a measure of how you can fill a via with copper. The AR is the PCB thickness to the hole diameter. Your circuit board’s reliability is key and a good AR is key for that. For microvias, the ideal AR is 0.75:1. That translates into making the hole much smaller than the board thickness. For through-hole vias, the ideal AR is 10:1. It works for plating without much problem. You can choose an AR greater than 10:1. But such an approach increases design costs and complexity. It may even cause reliability problems.

PCB Via Type vs. Size
| Via Type | What It Does | Size Requirements |
| Signal or Ground | It creates a path for electrical current. | It needs to be big enough to carry the highest expected current without a problem. |
| Thermal | It helps remove heat from a part or the board. | It should be big enough to keep stuff cool without causing damage to components or traces. |
| Tented | It stops current flow and helps with soldering. | The best size for these vias is 0.25 to 0.3 mm; smaller, filled vias use less material, but laser drilling may be needed for a thicker board. |
PCB Via Size Requirements
Vias are important when you design a PCB. How you design and where you put them matters. Sometimes a bad via can affect how well a board works.
Via Aspect Ratio Calculator
As a result, PCB design is only as good as the via aspect ratio. It compares the depth of a via to its width. The ratio influences how current is carried by the via. Less plating time is needed for a high aspect ratio. This creates a thicker layer. A thin layer may result from a low aspect ratio. It can lower the electricity it is capable of conducting.
Standard Via Sizes in Mils
Very small measurements are described by mils, a unit. How thick your PCB is will determine these sizes. And they depend on what the PCB manufacturer can do. On via sizes different manufacturers have different limits. Being so very important, choosing the right size is very important. And it will affect how much the board costs. It can also affect how reliable your board is if you choose a poorly sized size. Vias that are too small could fail to operate.
PCB Annular Ring Calculator
The copper ring surrounding a via is then called the annular ring. Its size is very important. If the via is weak, a small ring will do it. However, this breaks the copper pad’s bond. Good conductivity can lead to poor conductivity. Unshielded signals can hurt the reliability of your board because of this. A large annular ring, on the other hand, is more expensive. It can also reduce the density of board.
Via Plating Thickness
A thicker plating can be a means for helping conductivity. It can, however, also increase costs. May also make the board thicker, and plus. A thinner plating costs less. It can also lighten your board. But be careful. For this could affect the via’s conductivity and reliability.
Stub in PCB Layout
This is a piece of trace that is short, connected to a via. This can cause problems in your PCB. Signal reflection can happen via stubs. However, this can hurt the signal quality. You should keep stubs short. The shorter, the better. It reduces interference. Also the impedance of the stub should be checked. It has to match the trace impedance. For good signal integrity matching impedance is key.

Guidelines & Considerations for PCB Via Size Selection
Via Types
When you work with via types, remember what project you are working on. Different vias are needed for different projects. Larger holes work well if you have just one layer. You have flexibility without fill or extra tech. More current can be pushed through larger vias. And it also allows better heat dissipation.
Via Dimensions
How big your vias can be is dictated by the thickness. It is called the aspect ratio. Your vias work well on a proper aspect ratio. The bigger the board, the bigger the vias requirement. More current can be passed through larger vias. Smaller vias are enough as long as the board is thin. Small vias are smaller, consume less space. Always keep via size matching the board thickness.
Via Tolerances
This is range in which hole sizes are acceptable. You need to be specific on how this tolerance will be stipulated. This assures that the holes fit well. Most of the PCB suppliers have their own standards.
Selecting Suitable Technologies
Decide the technology you need. Do you need blind or buried vias? Then make sure you talk to your PCB supplier. They can assist you by developing the right stack up for your design. Always make sure that every requirement always communicates clearly. A better final product will result from this.
Annular Ring Specifications
This is important for the Class 2 and Class 3 boards. Annular ring should be at least 2 mils for microvias or laser drilled vias. For mechanically drilled vias it should be at least 4 mils. But, remember, the ring is measured in CAM software. The size of the drilled hole is considered.
PCB IPC Classifications
Class 2, also Class 3 boards have different standards. Class 2 boards are what is recommended for everyday electronics. Laptops and smartphones have them. And they can have some of small flaws. And because of this, they’re easier to inspect and quicker to make. High reliability devices are in class 3 boards. Military gear and pacemakers are used. These boards are very strict and reliable. Inspections are more and they are more costly. Products that need to work time and time again as good as the last time are best suited for class 3 boards.
Equipment Specifications
When making the size of vias on your PCB design, keep in mind the ability of the manufacturer. When buying PCBs, it’s important to go for the provider that has the latest technology. Doing so ensures that they can use your specific via size requirements. Many manufacturers may be otherwise without proper equipment. Or they may need to sub contract out the work to someone else.
PCB Density
Board that is dense has 65 to 120 connections per square inch. Also, look at hole density. A double-sided board of about 600 holes per square decimeter is very common. Current density is key too. Watch your copper track spacing. Place tracks located at equal spacings of their width. It prevents both signal issues and overheating. Better if components are placed close together if they are similar.
Via Filling Techniques and Plating Options
Defects in your PCB is caused by trapped substances. Conductive and non-conductive epoxy paste can be put into vias. Special electroplating chemistry is used for blind vias and via in-pads. However, if you want to move heat across the board, then go for a conductive fill. Make sure vias are sealed or cover with capped plating. The result is that during manufacturing buried via plating issues are prevented. You can avoid these problems by filling the vias with resin first. If you have a via in pad, you need to plate it.
Component Clearance
It is the space around the via. It should have enough space for all PCB components. The via could impede the component if clearance is too small. Assembly or even operation can be a problem. We suggest that the minimum clearance should be at least 0.1mm. That’s a good rule. This helps your components to be placed correctly.
Solder Mask
Getting those solder mask openings right is important. Your component pads should be a little smaller than these openings. This keeps solder paste from going down into the nearby pads. We also find tenting (covering the vias with solder mask) useful. Protects the vias from damage, and prevents solder leaking into them, which leads to shorts. But don’t tent vias with pad diameter bigger than 12 mils because it’ll cause solder voids and potential reliability issues.

How to Optimize Your Via Size Selections
Know How Much Current Your Traces Need to Handle
Signal, power and ground currents carried by vias. Each type needs them to work well together. Vias that are clearly able to transfer their signal are good. As a result, less loss and better performance. Ensure that your vias are safe for the current.
Follow Simple Guidelines for Trace Width and Spacing
Your design contains traces and vias. Surface components are connected by vias. Effective routing of your vias is good trace routing. Traces must be wide enough for the current. Space them just right, without interfering. That allows for better vias.
Stick To IPC-2222 Rules for Minimum Hole Sizes
You’ll first want to know what your component density classification is. Then you use simple formulas to find minimum hole sizes. For Level A, we add 0.25 mm to the maximum lead diameter. For Level B add 0.20 mm and for Level C add 0.25 mm. We will then decide the pad sizes via IPC‑2221. Pad diameters are calculated from the hole sizes.
Reduce The Number of Vias You Use
Use fewer vias when possible. Too many vias will choke up your vias. They will weaken the board and how it works. Less vias means better design. Instead, concentrate on how to route your traces. It means finding the best path for connections. A good routing means you need fewer vias.
Work With Your Manufacturer to Find Suitable Via Sizes
Working with your manufacturer will help make the best boards. Ask them what vias sizes they can drill. There are different capabilities among different manufacturers. Some can drill little holes, but others cannot. They have restrictions on the thickness of the board they can do. But understanding these limits helps you decide what via sizes are right for you.

Questions About PCB Via Sizes
What Is PCB Laser Via Size?
The PCB via laser drilled varies in size. Smallest is 0.001 inches (0.025 mm). Can be as small as 0.0005 inches. Can be large as 0.008 inches. Aspect ratio is usually 0.75:1. You often laser drill vias for blind and buried vias. Sequential lamination works well with them. They’re also in fine pitch BGAs.
What Is the Size of The Via Capture Pad?
It will depend upon your type and thickness of PCB. PCB’s thickness ranges from 1.5 mm>. Typically it is a 0.660 mm via capture pad in this case. The pad size for a large via is 0.7 mm and drill size is 0.3 mm. The drill size is 0.25 mm, and the pad size, 0.6 mm, is for medium via. Pad size is 0.5 mm and drill size is 0.2 mm for a small via. The maximum diameter for blind vias is 0.4 mm, with a pad of 450 μm. Similarly for buried vias the diameter is also 0.4mm but have pad dimensions of 300 μm.
How Small Can Vias Be?
Typically minimum-sized vias are in the 0.25 to 0.3 mm range. They require less material for these smaller vias. But again, if board depth varies, then they may need to be laser drilled. The minimum drill size is usually 0.25 mm. The smallest annular ring size is 0.15 mm. Ideally, you want to avoid going to these minimums.
How Do You Calculate PCB Size?
The length and the width in millimeters is used to calculate PCB size. Multiply these two numbers. Next, you have the area in square millimeters. Divide by 1,000,000 to change that to square meters. Take PCB design software for example. Open the PCB layout file, you can use in your software. Now place our components within the PCB outline. Adjust the outline size using “Move” tool. Finally, measure the outline box’s size.
Conclusion
On this PCBTok blog, we explained everything required for PCB via sizes. There were crucial ideas to understand for making informed design decisions, these were standards, types, and aspect ratios. We discussed everything from vias different types, size requirements and optimization opportunities to give you a bigger picture of how to improve your PCB design process.


Change Language